FIREBIRD Ink SKU: PHT50-W-1pcs

DTF Ink Bags for Mimaki TxF150-75 & TxF300-75

$54.00

Verified Compatibility
Formulated to directly replace Mimaki PHT50 ink.

Chips Available
Shop PHT50 Compatible Chips.

Ships Today
When ordered before 3:30 PM EST, Mon-Fri.

Size: Single (500 ml)

Legendary FIREBIRD Support
Our DTG Masters are ready to help you optimize!

FIREBIRD DTF Ink Bags for Mimaki TxF150-75 & TxF300-75 printers are intended to effortlessly replace Mimaki PHT50 ink, offering superior print characteristics and unrivaled value.

Specifications

  • Compatible Printers:  Mimaki TxF150-75, Mimaki TxF300-75, PHT50 compatible printers.
  • Available Ink Colors: White
  • Capacity: 500 ml / 500 cc 
  • Weight: 4lbs
  • Dimensions: 22 x 4 x 4 inch
  • Type: Replacement Ink Bag for Mimaki PHT50 compatible cartridge
  • Ink Type: Direct to Film (DTF)

Mimaki® and PHT50™ are trademarks of Mimaki Engineering Co. Ltd., which does not produce, endorse, warranty, or approve of the use of FIREBIRD Ink's third-party ink, pretreatment, and/or cleaning solutions which are non-genuine OEM products. FIREBIRD Ink will fully support and guarantee your 100% satisfaction, as we do with all of our products.

Ink Bag Replacement Instructions:

The lights above the Mimaki® TxF-150/300 printer indicate when an ink bag replacement is required due to low ink level or ink expiration (i.e. yellow light: low/end/expired [1 month] and red light: expired [2 months]).

Follow these steps:

  1. Remove the cartridge and open the lid by pressing each of the 4 tabs holding the cartridge together.
  2. Remove the used ink bag and replace with the new ink bag. Ensure that the nozzle tip is positioned correctly so that the bag is secure and the lid can be closed easily.
  3. (Optional) Ink Chip replacement – see instructions on reverse side.
    Note: The existing ink chip can be re-used, so long as it is not expired (past 2 months)
  4. 4) Now that the ink bag is installed, it is time to input the new weight of the cartridge + ink bag. Weigh the cartridge + ink bag on a gram scale. Note the weight (in grams).
  5. Insert the cartridge back into the correct slot.
  6. Correcting the Ink Cartridge Case Weight: select [MENU] > [Machine Setup], then press the [Enter] key. Select [Eco cartridge] > [Cartridge Weight], then press the [ENTER] key. Select the required ink slot, then press the [Enter] key. Enter the measured weight of cartridge + ink bag. The light above the cartridge should now be solid blue and ready to run.

Ink Chip Replacement (Optional):

For cost/environmental savings, it is possible to reuse an existing ink chip many times, so long as the chip does not expire (indicated on the printer with the error message: “Expiration”). However, when an ink chip expires, or if you wish to replace an ink chip when the ink bag is replaced, follow these steps:

  1. Remove the cartridge and open the lid by pressing each of the 4 tabs holding the cartridge together.
  2. Remove the used ink chip from the slot at the left edge of the cartridge. Replace with the new ink chip.
  3. Close the lid and ensure that all 4 tabs snap tightly back into place.

Note: If the lid is not fully closed, there may be a small gap at edge of the cartridge and chip (see dotted red box). This gap can prevent the printer from reading the chip correctly (the light above the cartridge bay will still be solid red).

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)